Transmissions, Transfer Cases & Slippers

Additional Information - (1) RC4WD 540 Crawler Brushed Motor (35T)Custom made to fit all popular Truck such as Bully, AX10, Trail Finder!

Spur Gear AX30672 48DP 87T for SCX10 Honcho Dingo CF100 Jeep There is no better way to improve a noisy drive train than a fresh spur gear. This is very easy to change over on your truck with just one...

Additional Information - Ultra Scale Hardened Steel Driveshaft (95mm - 130mm / 3.74" - 5.1") 5mm

Additional Information -

Additional Information -

Additional Information - RC4WD TCI Heavy Duty R4 Single Speed Scale Transmission

Additional Information - Bearings for small gear are AX1221. They are 9mm thick and small gear 16mm and larger one 28.5mm approximately.Gear set for Axial Transmissions

Additional Information - HIGH RATIO TRANSMISSION CONVERSION KIT FOR WRAITH

Additional Information - R3 Scale Single Speed Transmission This is the all new R3 Scale Single Speed transmission that is used in the Gelande 2.<

Additional Information - Motor Mount for R4 Transmission

Additional Information - Hardened Gear set for Axial Transmissions These are All 3 the including diff and idler gear for the Axail Racing Transmissions as fitted to the 'Old' AX10, 'New' AX10...

Additional Information - Full length measurements and the pins are set in about 5mm from each end

Additional Information - Axial SCX10 & AX10 Steel Outdrive Shaft Set (2pcs)Replaces the old aluminum version outdrive shaft [AX30404] in SCX10/AX10's. The Steel Outdrive Shaft is cross drilled for...

Additional Information - R3 Tranny Mounts For Trail Finder 2

Axial Wraith and Dig Transmission DIG Kit. With this KIT Axial's dig transmission case is easily upgradable for dig function which, when installed, gives you a three function transmission. The...

Additional Information - TF2 Long Drive Shaft Coupling for R3 Single Speed

Additional Information - • Transmission set• Molded plastic• Complete replacement transmission case for SCX10 and AX10

Additional Information - 1x R3 2 Speed Transmission Shafts

Additional Information - Skid plates for SCX10 and SCX10 II chassis Included two skid plates; SCX10 II transmission mount and AX10 Transmission mount Captured screw design, no lock nuts required...

Additional Information - R5 1/18 Mini Transmission V2 Specifications: Plastic Injection Molding Case FF-030 Micro Electric Motor Gear Ratios Pinion / Spur 10/55= 5.5:1 Delrin Spur Gear Slipper...

Additional Information - Axial’s new steel 32P pinion gears for the EXO Terra Buggy offer you an array of gearing options to fine tune torque and top speed.• Powder steel construction for durability•...

Additional Information - Shaft is 35mm long. Metal Drive Coupling for Trail Finder 2

CLEARANCE Limited Stock -� Hurry while stock lasts - Stock figure is liveAdditional Information - Fits:- MT10, Axial Wriath and TRX-4 REAR.

Additional Information - Ultra Scale Hardened Steel Driveshaft (145mm - 180mm / 5.70" - 7.08") 5mm

CLEARANCE Limited Stock -� Hurry while stock lasts - Stock figure is livePunisher Shaft II (70mm -

Additional Information - Axial slipper clutch pads are compatible with AX31026 Slipper Plate and AX31027 Spur gear. New an

Additional Information - U/J is metal and the shafts are plastic, but stronger than stock. There is alos a retainer built in to stop pins working loose. Ultra Punisher Shafts (83.7MM - 105MM / 3.29"...

Additional Information - 52T 32P Delrin Spur Gear

Additional Information - Axial Wraith Dig Transmission CaseUpgrade your current AX10 Scorpion o

Additional Information - RC4WD Scale Steel Punisher Shaft V2 (75mm - 95mm / 2.95'' - 3.74'')

Additional Information - Slipper Clutch Assembly for R3 and AX2 Transmissions<

Additional Information - 1x RC4WD Ultra Compact 4:1 Gear Reduction Unit for 540 Motor Decrease speed and increase torque!

Additional Information - Metal Drive Coupling for Gelande 2

Additional Information - R3 Single Speed Transmission Mounts

Additional Information - RC4WD Over/Under Drive Transfer Case   Specifications: 1.47 / 1 Gearing .8 Mod Gears Hardened Steel Gears Cast Casing Wide Gears

Additional Information - Low Profile Delrin Skid Plate for Std. TC (TF2 SWB)Specif

Additional Information - Ultra Scale Hardened Steel Driveshaft "Ver 2" (80mm - 110mm / 3.15" - 4.33")These are an extremely scale driveshaft that are durable and built like the real thing. Now in V

Additional Information - AX2 2 Speed Transmission for Axial Wraith & SCX10/Honcho

Additional Information - AX2 Heavy Duty Output Shaft