Suspension, Shocks, Springs etc
How To: Shock absorber basics and oil change
You know it’s time to change the oils in your shocks when you notice there isn’t enough oil or when you’re making changes to the damping setup or when the shocks are damaged and require taking apart. In any case, the shock oils should be changed 2–3 times during a season. The properties of the oils might fade or change over time. One problem is dirt and dust that gets into the shocks especially when driving in dusty conditions. When there’s dirt in the oils, the seals and other parts of the shocks will wear down faster compared to driving with clean oils.
When you’re changing the oils, start by removing the shock and cleaning it carefully. By cleaning the shock, you can make sure no sand grains or other particles will remain the shock that can damage it from the inside.
Do the following:
- Remove the shocks.
- Remove the spring from the shock to make handling easier.
- When cleaning the shock, also clean under the rubber boot on the shock shaft, if there is one.
Now, empty the shocks. You can use a single-use cup and place a paper towel in the bottom that will absorb the oil in itself. Remove the cap from the shock and place it on a paper towel. Now, pour the oil from the shock in the cup. Move the shock shaft up and down a couple of times to remove oil from under the piston. When most of the oil is removed, place the shock upside down on a paper towel so the remaining oil will come out. Do the same with the other shocks.
- If the oil that’s come out of the shock is dirty (dark and thick like jelly), remove and clean the seals at the bottom of the shock and rebuild the shock. By cleaning the seals, you can make sure the dirty oil containing sand and metal particles won’t wear down the shocks.
- If the oil that comes out of the shock is still “normal”, i.e. runny and transparent, it’ll be enough to clean the cylinder with a rolled-up piece of paper towel. Clean the cap as well and if you’re using caps with bladders, check the condition of the bladder and that it fits properly.
Now, you can add the oil. I’d recommend using a work stand to keep the shocks upright during the assembly.
- Pull the whole shock shaft out of the shock body before adding the oil.
- Fill the shock about halfway.
- Now, move the piston in the oil so that all the air gets out. Wait for a moment and move the piston again.
- Next, add more oil until it’s 1-2 mm from the top of the cylinder.
- Move the piston up and down and let them sit on the desk until all the air bubbles in the oil has disappeared.
The right way to proceed depends on the type of the shock. With all shock types, it’s essential that the shock is in an upright position so that the air bubbles can move right upwards.
There are several different cap types:
Emulsion shocks:
Air is allowed to mix with the oil. With this type of shocks, it’s particularly important to make sure there is no air in the shock when the shaft is pushed all the way up.
There are several types of caps for emulsion shocks
With the Bleeder type, the air is removed using the bleeding screw on the cap.
With the other cap types, the excess oil and air will come out through the threading on the cap.
Bleeder Cap on the left and without on the right
With both cap types, fill the shock cylinder up to the brim to make sure the space inside the cap will also fill up and any extra oil can come out.
- Fill the cylinder
- Prepare the caps: Remove the screw from the bleeder cap. Place seals
With bleeder screw. Screw in the cap. Screw in tightly using moderate force. Now, push in the shock shaft and the air and excess oil should come out of the bleeding screw hole. When you see that all excessive oil came out, you’ll know there’s only oil left in the shock. Screw the bleeding screw back in. Compress the shaft a few times. If there’s clear signs of air still in the shock, add more oil and try removing the air again.
If there’s no bleeding screw, fill the shock all the way up with oil. Before screwing on the cap, you can add a few drops of oil in the cap. Now screw in the cap loosely and carefully move the shaft all the way in. All excess oil and air should come out through the threading on the cap. Hold the shaft in and tighten the cap to get rid of the remaining excess oil. Now, compress the shock a couple of times and see if there is still air in the shaft.
There should be no rebound on an emulsion shock, i.e., when the piston is pushed all the way in it shouldn’t move outwards by itself once it’s released. It’s essential to have similar reaction in both shocks at one end (front/rear) of the car, so their functioning would be identical on both the left and right side.
Bladder shocks
If you’re using bladder caps, building the shock is similar to that in emulsion shocks without bleeder caps. Fill the cap with oil up to 1–2 mm from the brim, not all the way up because the bladder takes some space in the cap. With bladder caps you can adjust the rebound to make damping more progressive – the longer the shock travels, the stiffer it gets. A bladder will also keep the oil from foaming which makes the car move more smoothly during a longer drive.
When it comes to building, the only difference to emulsion shocks is that the rebound can be adjusted by how much of the piston shaft you push in before screwing the cap on.
- The farther you push the shaft in, the less you’ll have rebound.
- So, if you push the shaft all the way in, there’s no rebound and the shock works like an emulsion shock.
Adjust the rebound the way you want and hold it against the desk while you screw the cap on so the shaft won’t move outwards. When both shocks are ready, pump the shocks a couple times. Do the same on both shocks and check that the shaft comes back out the same on both shocks. If the one of them comes out more, there’s too much oil in it. Or if it doesn’t come out enough, there’s too little oil in it.
Tip! You get a suitable amount of rebound for a basic setup when you leave about 1/3 of the shaft out. You can build the shock with the shaft pushed all the way up. Both will result in a smooth and neutral outcome.
Note! See, however, that the shock shaft doesn’t damage the bladder and the shaft doesn’t squeeze up the bladder.
- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
Element RC FT Enduro Links 93mm EL42184
Element RC
RRP £8.49Additional Information - ELEMENT RC FT ENDURO LINKS 93MMThe Enduro links are now sold separately by length.FEATURESLinks are available in straight and high clearance (HC) geometryMade from high strength steelAll FT links are nickel plated with a...EL42184RRP £8.49 -
FTX Outback Mini X/XP Optional Oil Filled Aluminum Shocks (4) FTX9447
FTX
RRP £37.99Additional Information - FTX OUTBACK MINI X/XP OPTIONAL OIL FILLED ALUMINUM SHOCKS (4FTX9447RRP £37.99 -
FTX Mini Outback 2.0 Aluminium Shock Upgrade Set (4Pc) FTX9325
FTX
RRP £19.99Additional Information - FTX MINI OUTBACK 2.0 ALUMINIUM SHOCK UPGRADE SET (4PC)FTX9325RRP £19.99 -
Element RC Enduro Shock Internals EL42081
Element RC
RRP £10.49Additional Information - ELEMENT RC ENDURO SHOCK INTERNALSEL42081RRP £10.49 -
Element RC Enduro Rod Ends EL42040
Element RC
RRP £18.49Additional Information - ELEMENT RC ENDURO ROD ENDSEL42040RRP £18.49 -
ProLine Power Stroke SCX10 Scaler SHOCKS 90 95mm Aly PRE BUILT 2 springs 6060-00
Pro-Line
MSRP: £44.99Now: £35.99Was: £44.99PRO-LINE PRO-LINE POWERSTROKE SCALER SHOCKS 90MM-95MM PAIRPro-Line Pro-Line Powerstroke Scaler Shocks 90mm-95mm Pair6060-00MSRP: £44.99Now: £35.99Was: £44.99Qty in Cart: 0Quantity:Price:MSRP: £44.99Now: £35.99Was: £44.99Subtotal: -
Fastrax Racing Pure Silicone Oil 20wt FAST60-20 200cst 50ml easy pour bottle
Fastrax
RRP £3.99Additional Information - Perfect for those small scale crawlers and scale trucks like the FMS FCX24. This is a real must have in you tool box, an oil change can make all the difference to oil dirty shocks. FASTRAX RACING PURE SILICONE OIL 20WT FAST60-20...FAST60-20RRP £3.99 -
Fastrax Racing Pure Silicone Oil 50wt FAST60-50 600cst 50ml easy pour bottle
Fastrax
RRP £3.99Additional Information - This is a real must have in you tool box, an oil change can make all the difference to oil dirty shocks. FASTRAX RACING PURE SILICONE OIL 50WT FAST60-50 See below for other part numbers & wt. Remember Thinner oil / softer...FAST60-50RRP £3.99 -
Fastrax Racing Pure Silicone Oil 40wt FAST60-40 500cst 50ml easy pour bottle
Fastrax
RRP £3.99Additional Information - Great for Buggues and Truggies. This is a real must have in you tool box, an oil change can make all the difference to oil dirty shocks. FASTRAX RACING PURE SILICONE OIL 40WT FAST60-40 See below for other part numbers & wt...FAST60-40RRP £3.99 -
SSD Shock Rebuild Kit (2) SSD00311 Seal spacers X rings 2mm E clip SSD-RC
SSD
RRP £10.50Additional Information - DESCRIPTION Part No. SSD00311 Shock Rebuild Kit FEATURES Seal, spacers X rings Enough parts to rebuild two...SSD00311RRP £10.50 -
Windshield Guard for Axial SCX10 III Early Ford Bronco VVV-C1281 RC4WD Mesh
CCHand
RRP £25.99Additional Information - Windshield Guard for Axial SCX10 III Early Ford BroncoSpecifications:Stainless SteelLaser EtchingGuard Width: 2.99in / 76mmGuard Length: 7.44in / 189mmGuard Thickness: 0.01in / 0.5mmTotal Weight: 1.30oz / 37gShown painted Black...VVV-C1281RRP £25.99 -
106mm (4.17") Internally Threaded Aluminum Link SILVER x4 Z-S1501 RC4WD links
RC4WD
RRP £14.49Additional Information - 106mm (4.17") Internally Threaded Aluminum Link (Silver) (4)Specifications: Smooth Anodized Coating 3mm Female Threading Length: 4.17in / 106mm OD: 0.23in / 6mm Thread Depth: 0.59in / 15mm Weight: 0.32oz / 9gWhat's Included: 4x...Z-S1501RRP £14.49 -
RC4WD Trail Finder 3 Front Shock Hoops Z-S2129 RC4WD aluminium mounts TF3
RC4WD
RRP £26.49Additional Information - RC4WD Trail Finder 3 Front Shock HoopsSpecifications:CNC MachinedBillet AluminumBlack Anodized FinishTotal Weight: 0.59oz / 17gShown installed on RC4WD Trail Finder 3 RTR Chassis for example (Not Included)What's Included:1x RC4WD...Z-S2129RRP £26.49 -
U-Bolt Kit for Yota 2 and K44 Axles Z-S2128 RC4WD leaf spring Mounts for 2 axles
RC4WD
MSRP: £22.49RRP £19.99Additional Information - U-Bolt Kit for Yota 2 and K44 AxlesSpecifications:Steel and Aluminum PartsDesigned to fit Yota 2 Axle onlyTotal Weight: 1.05oz / 29.9gShown installed on RC4WD Trail Finder 3 RTR Chassis for example (Not Included)What's...Z-S2128MSRP: £22.49RRP £19.99 -
RC4WD Trail Finder 3 W56 2-Speed Transmission Shifting Assembly Z-S2126 RC4WD
RC4WD
MSRP: £39.49RRP £35.49Additional Information - RC4WD Trail Finder 3 W56 2-Speed Transmission Shifting Assembly Specifications:Stamped SteelStainless SteelBillet AluminumCNC MachinedTotal Weight: 1.04oz / 29.7gWhat's Included:1x RC4WD Trail Finder 3 W56 2-Speed Transmission...Z-S2126MSRP: £39.49RRP £35.49 -
RC4WD Trail Finder 3 W56 2-Speed Transmission w/ Transfer Case Z-S2121 RC4WD
RC4WD
MSRP: £23.99RRP £21.49Additional Information - RC4WD Trail Finder 3 W56 2-Speed Transmission W/ Transfer CaseSpecifications:Durable Black Nylon Reinforced PlasticOnly Plastic Housing FrameTotal Weight: 2.75oz / 78gShown with RC4WD Trail Finder 3 Transfer Case Replacement...Z-S2121MSRP: £23.99RRP £21.49 -
RC4WD Trail Finder 3 Shifting and Servo Arm Assembly Z-S2112 RC4WD Complete TF3
RC4WD
MSRP: £45.99RRP £40.99Additional Information - RC4WD Trail Finder 3 Shifting and Servo Arm AssemblySpecifications:CNC MachinedBillet AluminumBlack Anodized FinishTotal Weight: 1.12oz / 32gShown installed on RC4WD Trail Finder 3 RTR Chassis for example (Not Included)What's...Z-S2112MSRP: £45.99RRP £40.99 -
Suspension Links for Cross Country Off-Road Chassis Z-S2048 RC4WD
RC4WD
MSRP: £26.49RRP £23.49Additional Information - Suspension Links for?�Cross Country Off-Road ChassisSpecifications:CNC MachinedBillet AluminumBlack Anodized FinishTotal Weight: 1.32oz / 37.6gShown installed on RC4WD Cross Country Off-Road RTR with Chubby Mini 3 TON Scale Jack...Z-S2048MSRP: £26.49RRP £23.49 -
Spring Damper Set for 1/24 Trail Finder 2 Z-S2046 RC4WD Shocks 5mm 23mm Length
RC4WD
RRP £22.49Additional Information - Spring Damper Set for 1/24 Trail Finder 2Specifications:ABS Plastic Injection MoldingHole to Hole (Compressed): 0.70in / 18mmHole to Hole (Uncompressed): 0.90in / 23mmOverall Length: 1.10in / 28mmTravel Length: 0.19in / 5.0mmEach...Z-S2046RRP £22.49 -
Trailing Arm SMT10 Yeti Bomber Carbon Assault 10th Monster Truck Z-S2008 RC4WD
RC4WD
MSRP: £44.99Now: £38.99Was: £44.99Additional Information - Trailing Arm for SMT10, Yeti, Bomber, Carbon Assault 1/10th Monster TruckSpecifications:CNC MachinedBillet AluminumSilver Anodized Finish?�Length: 5.11in / 129.8mmTotal Weight: 2.79oz / 79.3gShown installed on RC4WD Carbon...Z-S2008MSRP: £44.99Now: £38.99Was: £44.99 -
RC4WD Bilstein SZ Series 70mm Scale Shock Absorbers Z-D0083 Internal Spring RC
RC4WD
RRP £47.49Additional Information - RC4WD Bilstein SZ Series 70mm Scale Shock AbsorbersThese are the all new RC4WD Bilstein SZ Series 70mm Scale Shock Absorbers. Designed to minimize the vibrations from the springs, these shocks come in a clean silver anodized...Z-D0083RRP £47.49 -
RC4WD Bilstein SZ Series 60mm Scale Shock Absorbers Z-D0082 Internal Spring RC
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Bilstein SZ Series 60mm Scale Shock AbsorbersThese are the all new RC4WD Bilstein SZ Series 60mm Scale Shock Absorbers. Designed to minimize the vibrations from the springs, these shocks come in a clean silver anodized...Z-D0082MSRP: £47.49RRP £40.99 -
RC4WD Bilstein SZ Series 50mm Scale Shock Absorbers Z-D0081 Internal Spring RC
RC4WD
RRP £47.49Additional Information - RC4WD Bilstein SZ Series 50mm Scale Shock AbsorbersThese are the all new RC4WD Bilstein SZ Series 50mm Scale Shock Absorbers. Designed to minimize the vibrations from the springs, these shocks come in a clean silver anodized...Z-D0081RRP £47.49 -
Steering Links for Wide D44 Axles Z-S2027 RC4WD Axle link 170 74mm Set
RC4WD
MSRP: £13.49RRP £11.99Additional Information - Steering Links for Wide D44 AxlesSpecifications:CNC MachinedBillet AluminumSilver Anodized Finish�?�Total Weight: 1.57oz / 44.6gShown installed on RC4WD Carbon Assault 1/10th Monster Truck w/ Manticore Lexan Body Set (Z-RTR0041)...Z-S2027MSRP: £13.49RRP £11.99 -
Upper Links for Carbon Assault 1/10th Monster Truck Z-S2009 RC4WD Suspension
RC4WD
RRP £17.99Additional Information - Upper Links for Carbon Assault 1/10th Monster TruckSpecifications:CNC MachinedBillet AluminumSilver Anodized Finish�?�Total Weight: 2.53oz / 71.8gShown installed on RC4WD Carbon Assault 1/10th Monster Truck w/ Manticore Lexan...Z-S2009RRP £17.99 -
Suspension Link Set for RC4WD C2X Competition Truck Z-S2036 Links C 2X Steering
RC4WD
RRP £21.49Additional Information - Suspension Link Set for RC4WD C2X Competition TruckSpecifications:CNC MachinedBillet AluminumBlack Anodized Finish?�Total Weight: 2.94oz / 83.5gShown installed on RC4WD C2X Class 2 Competition Truck w/ Mojave II 4 Door Body...Z-S2036RRP £21.49 -
Shock Hoops SCX10 II AX31380 Axial Hoop Body Post Mount Chassis SCX102
Axial
MSRP: £10.99Now: £10.44Was: £14.99Additional Information - SCX10 shock hoops parts tree Molded plastic shock hoops Compatible with SCX10 and SCX10 II chassis Genuine Axial PartsAX31380MSRP: £10.99Now: £10.44Was: £14.99 -
Element RC FT Enduro Shock Bushings, Steel EL42055 Balls Enduro (4) bush
Element RC
RRP £7.49Additional Information - Element RC FT Enduro Shock Bushings, Steel EL42055. Silver steel shoccl bushes / balls, sold in a packet of 4. These are an Factory Team upgrade part.EL42055RRP £7.49 -
Element RC Enduro Pivot Balls Steel EL42054 suspension ball Enduro Sendero (10)
Element RC
MSRP: £18.49RRP £17.00Additional Information - Element RC Enduro Pivot Balls, Steel EL42054. Replacement picot suspension balls in silver supplied as a packet of 10.EL42054MSRP: £18.49RRP £17.00 -
Element RC Enduro Shock Mounts, HARD EL42013 Stiff less flex upgrade mount
Element RC
RRP £12.49Additional Information - Element RC Enduro Shock Mounts, Hard EL42013. Upgrade to standard parts, they are stiffer giving less flex.EL42013RRP £12.49 -
Element RC Shock Springs, Blue, 2.09 lb/in, L63 mm EL42090 Enduro Spring
Element RC
MSRP: £8.49RRP £6.29Additional Information - Element RC Shock Springs, Blue, 2.09 Lb/In, L63 Mm EL42090 Packet contains just two springs, one pair.EL42090MSRP: £8.49RRP £6.29 -
RC4WD Rock Krawler Link Package AE Element RC Enduro Sendero RTR Truck Z-S1996
RC4WD
RRP £35.49RC4WD Rock Krawler Link Package for AE Element RC Enduro Sendero RTR TruckThe new Rock Krawler Link package is just what you need to top off your AE Element RC Enduro Sendero RTR Truck. The Rock Krawler links are CNC machined in billet aluminum...Z-S1996RRP £35.49 -
RC4WD Rancho RS9000 XL Shock Absorbers 100mm Z-D0079 TF2 G2 Suspension Shocks
RC4WD
RRP £47.49Additional Information - RC4WD Rancho RS9000 XL Shock Absorbers 100mmThis is the all new Licensed Scale Shock to hit the market. Licensed from Rancho. These new shocks feature a complete new design from the ground up and are built and ready to handle the...Z-D0079RRP £47.49 -
RC4WD Rancho RS9000 XL Shock Absorbers 90mm Z-D0078 TF2 G2 Suspension Shocks
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Rancho RS9000 XL Shock Absorbers 90mmThis is the all new Licensed Scale Shock to hit the market. Licensed from Rancho. These new shocks feature a complete new design from the ground up and are built and ready to handle the...Z-D0078MSRP: £47.49RRP £40.99 -
RC4WD Rancho RS9000 XL Shock Absorbers 80mm Z-D0077 TF2 G2 Suspension Shocks
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Rancho RS9000 XL Shock Absorbers 80mm This is the all new Licensed Scale Shock to hit the market. Licensed from Rancho. These new shocks feature a complete new design from the ground up and are built and ready to handle...Z-D0077MSRP: £47.49RRP £40.99 -
The Ultimate Scale Shocks 90mm SILVER RC4WD Z-D0001 Scaler absorber 90mm TF2
RC4WD
MSRP: £40.99RRP £34.99Additional Information - 2x The Ultimate Scale Shocks 90mm (Silver)At 9mm OD, this is the most Scale and precision made Suspension Shocks Available on the market. Along with our next gen fine tuned super soft internal Springs.Specifications:CNC...Z-D0001MSRP: £40.99RRP £34.99 -
The Ultimate Scale Shocks 70mm SILVER Shock Absorber RC4WD Z-D0004 rcBitz TF2
RC4WD
MSRP: £27.49RRP £22.99Additional Information - The Ultimate Scale Shocks 70mm (Silver)At 9mm OD, this is the most Scale and Precision Made Suspension Shocks available on the market. Along with our next gen fine Tuned Super Soft Internal Springs.Specifications:CNC Machined...Z-D0004MSRP: £27.49RRP £22.99 -
Super Soft Flex Leaf Springs for Gelande II (4) Z-S1897 RC4WD G2 101mm Spring
RC4WD
RRP £40.99Additional Information - Super Soft Flex Leaf Springs for Gelande II (4)Specifications:Super Durable Steel Leaf SpringsSoft Springs increases articulation over obstaclesScrew Hole OD: 0.12in / 3mmLength: 3.97in / 100.8mmWidth: 0.27in / 7.0mmTotal Weight:...Z-S1897RRP £40.99 -
89mm (3.5") Internally Threaded Aluminum Link (Silver) (4) Z-S1499 RC4WD M3 6mm
RC4WD
RRP £12.9989mm (3.5") Internally Threaded Aluminum Link (Silver) (4)Specifications: Smooth Anodized Coating3mm Female ThreadingLength: 3.5in / 89mmOD: 0.23in / 6mmThread Depth: 0.39in / 10mmWeight: 0.24oz / 7gWhat's Included: 4x 89mm (3.5") Internally Threaded...Z-S1499RRP £12.99 -
79mm (3.11") Internally Threaded Aluminum Link (Black) (4) Z-S1427 RC4WD M3 6mm
RC4WD
RRP £12.99Additional Information - 79mm (3.11") Internally Threaded Aluminum Link (Black) (4)Photo shows various sizes available (you only get the size listed)Specifications: Smooth Anodized Coating 3mm Female Threading 6mm Outside Diameter 79mm (3.11") End to...Z-S1427RRP £12.99