Suspension, Shocks, Springs etc
How To: Shock absorber basics and oil change
You know it’s time to change the oils in your shocks when you notice there isn’t enough oil or when you’re making changes to the damping setup or when the shocks are damaged and require taking apart. In any case, the shock oils should be changed 2–3 times during a season. The properties of the oils might fade or change over time. One problem is dirt and dust that gets into the shocks especially when driving in dusty conditions. When there’s dirt in the oils, the seals and other parts of the shocks will wear down faster compared to driving with clean oils.
When you’re changing the oils, start by removing the shock and cleaning it carefully. By cleaning the shock, you can make sure no sand grains or other particles will remain the shock that can damage it from the inside.
Do the following:
- Remove the shocks.
- Remove the spring from the shock to make handling easier.
- When cleaning the shock, also clean under the rubber boot on the shock shaft, if there is one.
Now, empty the shocks. You can use a single-use cup and place a paper towel in the bottom that will absorb the oil in itself. Remove the cap from the shock and place it on a paper towel. Now, pour the oil from the shock in the cup. Move the shock shaft up and down a couple of times to remove oil from under the piston. When most of the oil is removed, place the shock upside down on a paper towel so the remaining oil will come out. Do the same with the other shocks.
- If the oil that’s come out of the shock is dirty (dark and thick like jelly), remove and clean the seals at the bottom of the shock and rebuild the shock. By cleaning the seals, you can make sure the dirty oil containing sand and metal particles won’t wear down the shocks.
- If the oil that comes out of the shock is still “normal”, i.e. runny and transparent, it’ll be enough to clean the cylinder with a rolled-up piece of paper towel. Clean the cap as well and if you’re using caps with bladders, check the condition of the bladder and that it fits properly.
Now, you can add the oil. I’d recommend using a work stand to keep the shocks upright during the assembly.
- Pull the whole shock shaft out of the shock body before adding the oil.
- Fill the shock about halfway.
- Now, move the piston in the oil so that all the air gets out. Wait for a moment and move the piston again.
- Next, add more oil until it’s 1-2 mm from the top of the cylinder.
- Move the piston up and down and let them sit on the desk until all the air bubbles in the oil has disappeared.
The right way to proceed depends on the type of the shock. With all shock types, it’s essential that the shock is in an upright position so that the air bubbles can move right upwards.
There are several different cap types:
Emulsion shocks:
Air is allowed to mix with the oil. With this type of shocks, it’s particularly important to make sure there is no air in the shock when the shaft is pushed all the way up.
There are several types of caps for emulsion shocks
With the Bleeder type, the air is removed using the bleeding screw on the cap.
With the other cap types, the excess oil and air will come out through the threading on the cap.
Bleeder Cap on the left and without on the right
With both cap types, fill the shock cylinder up to the brim to make sure the space inside the cap will also fill up and any extra oil can come out.
- Fill the cylinder
- Prepare the caps: Remove the screw from the bleeder cap. Place seals
With bleeder screw. Screw in the cap. Screw in tightly using moderate force. Now, push in the shock shaft and the air and excess oil should come out of the bleeding screw hole. When you see that all excessive oil came out, you’ll know there’s only oil left in the shock. Screw the bleeding screw back in. Compress the shaft a few times. If there’s clear signs of air still in the shock, add more oil and try removing the air again.
If there’s no bleeding screw, fill the shock all the way up with oil. Before screwing on the cap, you can add a few drops of oil in the cap. Now screw in the cap loosely and carefully move the shaft all the way in. All excess oil and air should come out through the threading on the cap. Hold the shaft in and tighten the cap to get rid of the remaining excess oil. Now, compress the shock a couple of times and see if there is still air in the shaft.
There should be no rebound on an emulsion shock, i.e., when the piston is pushed all the way in it shouldn’t move outwards by itself once it’s released. It’s essential to have similar reaction in both shocks at one end (front/rear) of the car, so their functioning would be identical on both the left and right side.
Bladder shocks
If you’re using bladder caps, building the shock is similar to that in emulsion shocks without bleeder caps. Fill the cap with oil up to 1–2 mm from the brim, not all the way up because the bladder takes some space in the cap. With bladder caps you can adjust the rebound to make damping more progressive – the longer the shock travels, the stiffer it gets. A bladder will also keep the oil from foaming which makes the car move more smoothly during a longer drive.
When it comes to building, the only difference to emulsion shocks is that the rebound can be adjusted by how much of the piston shaft you push in before screwing the cap on.
- The farther you push the shaft in, the less you’ll have rebound.
- So, if you push the shaft all the way in, there’s no rebound and the shock works like an emulsion shock.
Adjust the rebound the way you want and hold it against the desk while you screw the cap on so the shaft won’t move outwards. When both shocks are ready, pump the shocks a couple times. Do the same on both shocks and check that the shaft comes back out the same on both shocks. If the one of them comes out more, there’s too much oil in it. Or if it doesn’t come out enough, there’s too little oil in it.
Tip! You get a suitable amount of rebound for a basic setup when you leave about 1/3 of the shaft out. You can build the shock with the shaft pushed all the way up. Both will result in a smooth and neutral outcome.
Note! See, however, that the shock shaft doesn’t damage the bladder and the shaft doesn’t squeeze up the bladder.
- Product
- Qty in Cart
- Quantity
- Price
- Subtotal
-
The Ultimate Scale Shocks 70mm SILVER Shock Absorber RC4WD Z-D0004 rcBitz TF2
RC4WD
MSRP: £27.49RRP £22.99Additional Information - The Ultimate Scale Shocks 70mm (Silver)At 9mm OD, this is the most Scale and Precision Made Suspension Shocks available on the market. Along with our next gen fine Tuned Super Soft Internal Springs.Specifications:CNC Machined...Z-D0004MSRP: £27.49RRP £22.99 -
Red Super Soft Flex Leaf Springs 4 RC4WD Trail Finder Direct replacement Z-S0570
RC4WD
RRP £40.99Additional Information - 4x Red Edition Super Soft Flex Leaf SpringsOur new flex leaf springs are 35% softer than stock, manufactured out of high alloy spring steel. Offer more flex and improve articulation!Click here to read a review about these leaf...Z-S0570RRP £40.99 -
Reverse Mount Spring Hanger Conversion Kit for TF2 MWB LWB Z-S1923 RC4WD
RC4WD
RRP £27.49Additional Information - Reverse Mount Spring Hanger Conversion Kit for TF2 and TF2 LWB Specifications: Heavy Duty Stamped Steel Black Powder-coated Finish Total Weight: 0.36oz / 10.0g Shown installed on RC4WD Trail Finder 2 "LWB" RTR...Z-S1923RRP £27.49 -
Soft Steel Leaf Spring Trail Finder 2 4 Sets 25% softer MORE Flex RC4WD Z-S0518
RC4WD
MSRP: £40.99RRP £34.99Additional Information - 4x Soft Leaf Springs for Trail Finder 2These leaf springs are 25% softer than stock Tamiya High Lift Leaf Springs, which allows for more flex!Specifications:Super dubrable steel leaf SpringsStiff Spring increases payload...Z-S0518MSRP: £40.99RRP £34.99 -
Dual Spring 80mm Scale Black Shocks Ver 2 BlackZ-D0039 Gelande II G2 RC4WD
RC4WD
MSRP: £40.99RRP £34.99Additional Information - Dual Spring 80mm Scale Black Shocks (Ver 2)Featuring a entirely new internal design, the Dual Spring (Ver 2) shocks are ready for any adventure. These now hold oil and have true performance in mind. Specifications: ...Z-D0039MSRP: £40.99RRP £34.99 -
Gelande 2 Front 3 Link & Panhard Mount BLACK Z-S0794 G2 II D90 Pan Hard RC4WD
RC4WD
MSRP: £32.99RRP £28.99Additional Information - Gelande 2 Front 3 Link & Panhard Mount (Black)Specifications:CNC Machined PartsBlack Smooth AnodizedShown what is included in this kitShown installed on Yota II Axle and Gelande 2 for example only (Not Included)What's...Z-S0794MSRP: £32.99RRP £28.99 -
Billet Steely M3 Rod End Heim Joint 10 Stainless Steel Suspension RC4WD Z-S1446
RC4WD
MSRP: £40.99RRP £34.99Additional Information - Steely M3 Rod End (Heim Joint) (10) Steely rod end is our 3rd generation full metal rod end. Not only it is extremly scale, it is also compact in size. Each Steely is super durable and machined out of billet stainless steel...Z-S1446MSRP: £40.99RRP £34.99 -
RC4WD Axle U Bolt fitting Kit for Leaf Springs Yota II G2 Gelande II 1 axle set Z-S0304
RC4WD
RRP £40.99Additional Information - Axle U Bolt KitSpecifications:CNC Machined PartsEngineered by RC4WDShown installed with RC4WD Yota II Ultimate Scale Cast Axle (Rear) (Z-A0081) and RC4WD Soft Steel Leaf Spring for Trail Finder 2 (Z-S0518) for example (Not...Z-S0304RRP £40.99 -
Ultimate Axle 4 Link Upper Suspension Mount K44 Trail Finder 2 TF2 Yota Z-S0133
RC4WD
MSRP: £34.49RRP £29.99Additional Information - Ultimate Axle 4 Link MountThis is the 4 Link Mount for the several Ultimate Scale Axles. This will allow you to turn many Axles from Leaf Spring setup to a 4 Link. Allowing your truck more articulation.Specifications:CNC...Z-S0133MSRP: £34.49RRP £29.99 -
The Ultimate Scale Shocks 80mm SILVER Shock Absorber RC4WD Z-D0005 rcBitz G2
RC4WD
MSRP: £40.99RRP £34.99Additional Information - 2x The Ultimate Scale Shocks 80mm (Silver) At 9mm OD, this is the most scale and precision made suspension shocks available on the market. Along with our next gen fine tuned super soft internal springs. ...Z-D0005MSRP: £40.99RRP £34.99 -
10 Aluminum Black M3 Rod End w/ Steel Ball 28mm long RC4WD Z-S1420 Suspension
RC4WD
MSRP: £27.49RRP £22.99Additional Information - Aluminum Black M3 Rod End with Steel Ball (10)Superior in durability and shiny finish! Made with advanced manufacturing technology!Specifications:Manufactured & Engineered by RC4WD USAGeneration II Rod End technology28mm Long...Z-S1420MSRP: £27.49RRP £22.99 -
Super Soft Flex Leaf Springs TF2 4 Z-S1815 RC4WD Direct fit Trail finder MWB LWB
RC4WD
MSRP: £40.99RRP £35.49Additional Information - Super Soft Flex Leaf Springs for TF2 (4)Specifications: Super Durable Steel Leaf Springs Stiff Spring Increases Payload Capacity Simple Installation, No Modifications Required Total Length: 4.94in / 125.5mmTotal Weight: 1.5oz...Z-S1815MSRP: £40.99RRP £35.49 -
RC4WD Superlift SUPERIDE 100MM SCALE SHOCK Absorbers Shocks WHITE Z-D0032
RC4WD
MSRP: £44.99RRP £40.49Additional Information - RC4WD Superlift Superide 100mm Scale Shock Absorbers This is the all new Licensed Scale Shock to hit the market. Licensed from Superlift Suspension Systems. These new shocks feature a complete new design from the ground up and...Z-D0032MSRP: £44.99RRP £40.49 -
Axial RTR Alluminium Steering Link Upgrade Kit for the Axial AX10 SCX10 Add strength
Axial
RRP £24.99Axial RTR Steering Upgrade Kit for the Axial AX10 & SCX10 This kit has all you need to replaces stock plastic steering links included on the Axial AX10 RTC's and SCX10 RTR's, with grey aluminium links. Adding this kit will...AX30426RRP £24.99 -
The Ultimate Scale Shocks 90mm SILVER RC4WD Z-D0001 Scaler absorber 90mm TF2
RC4WD
MSRP: £40.99RRP £34.99Additional Information - 2x The Ultimate Scale Shocks 90mm (Silver)At 9mm OD, this is the most Scale and precision made Suspension Shocks Available on the market. Along with our next gen fine tuned super soft internal Springs.Specifications:CNC...Z-D0001MSRP: £40.99RRP £34.99 -
RC4WD Rancho RS9000 XL Shock Absorbers 90mm Z-D0078 TF2 G2 Suspension Shocks
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Rancho RS9000 XL Shock Absorbers 90mmThis is the all new Licensed Scale Shock to hit the market. Licensed from Rancho. These new shocks feature a complete new design from the ground up and are built and ready to handle the...Z-D0078MSRP: £47.49RRP £40.99 -
The Ultimate Scale Shocks 60mm BLACK Shock Absorber RC4WD Z-D0008 rcBitz scaler
RC4WD
MSRP: £40.99RRP £34.99Additional Information - 2x The Ultimate Scale Shocks 60mm (Black)At 9mm OD, this is the most scale and precision made suspension shocks available on the market. Along with our next gen fine tuned super soft internal springs.Specifications:CNC Machined...Z-D0008MSRP: £40.99RRP £34.99 -
Replacement Leaf Springs for TF2 SWB Short Wheel Base RC4WD Z-S1717 Leafs Spring
RC4WD
MSRP: £40.99RRP £34.99Additional Information - Replacement Leaf Springs for TF2 SWB (4)Specifications:Super Durable Steel Leaf SpringsStiff Spring Increases Payload CapacitySimple Installation, No Modifications RequiredScrew Hole OD: 0.12in / 3mmTotal Length: 4.171in /...Z-S1717MSRP: £40.99RRP £34.99 -
AXIAL SCX10 WHEEL WELLS .04" CLEAR Protect your electronics AX31150 Floor Pan
Axial
MSRP: £34.99RRP £32.50Additional Information - AXIAL SCX10 WHEEL WELLS .04" CLEARThe SCX10 Wheel Wells give your rig the final missing elements: the full body look and under carriage protection. The clear polycarbonate plastic pieces provide you with enough pre-shaped...AX31150MSRP: £34.99RRP £32.50 -
RC4WD Bilstein SZ Series 80mm Scale Shock Absorbers Z-D0072 TF2 Front G2
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Bilstein SZ Series 80mm Scale Shock AbsorbersThese are the all new RC4WD Bilstein SZ Series 80mm Scale Shock Absorbers. Designed to minimize the vibrations from the springs, these shocks come in a clean silver anodized ...Z-D0072MSRP: £47.49RRP £40.99 -
RC4WD Rock Krawler Complete Link Package for Axial SCX10 II Z-S1873 Alloy links
RC4WD
MSRP: £39.49RRP £35.49RC4WD Rock Krawler Complete Link Package for Axial SCX10 II The new Rock Krawler Complete Link Package for Axial SCX10 II is just what you need to top off your Axial SCX10 II. The Rock Krawler links are CNC machined in billet aluminum with a...Z-S1873MSRP: £39.49RRP £35.49Qty in Cart: 0Quantity:Price:MSRP: £39.49RRP £35.49Subtotal: -
Aluminum Mini M3 Rod End with Steel Ball x10 Z-S1555 SILVER Shock Bottom rcBitz
RC4WD
MSRP: £27.49RRP £22.99Additional Information - Aluminum Mini M3 Rod End with Steel Ball (10) Works for with any Shocks that has a 3mm Shaft!Specifications: Manufactured & Engineered by RC4WD USA14Lmm ong & 5.6mm Diameter (Shaft Area) & 9mm Diameter (Ball...Z-S1555MSRP: £27.49RRP £22.99 -
RC4WD Bilstein SZ Series 60mm Scale Shock Absorbers Z-D0082 Internal Spring RC
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Bilstein SZ Series 60mm Scale Shock AbsorbersThese are the all new RC4WD Bilstein SZ Series 60mm Scale Shock Absorbers. Designed to minimize the vibrations from the springs, these shocks come in a clean silver anodized...Z-D0082MSRP: £47.49RRP £40.99 -
RC4WD Bilstein SZ Series 90mm Scale Shock Absorbers Z-D0075 Trail Finder REAR
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Bilstein SZ Series 90mm Scale Shock AbsorbersThese are the all new RC4WD Bilstein SZ Series 90mm Scale Shock Absorbers. Designed to minimize the vibrations from the springs, these shocks come in a clean silver...Z-D0075MSRP: £47.49RRP £40.99 -
M3 Long Straight Aluminum Rod Ends BLACK 10 RC4WD Z-S1652 28mm Links RC Crawler
RC4WD
MSRP: £40.99RRP £34.99Additional Information - M3 Long Straight Aluminum Rod Ends (Black) (10)Perfect upgrade to replace your plastic rod ends. The aluminum rod ends are a great heavy duty upgrade replacement. Direct replacement to Z-S0403.Specifications:Manufactured &...Z-S1652MSRP: £40.99RRP £34.99 -
Windshield Guard for Axial SCX10 III Early Ford Bronco VVV-C1281 RC4WD Mesh
CCHand
RRP £25.99Additional Information - Windshield Guard for Axial SCX10 III Early Ford BroncoSpecifications:Stainless SteelLaser EtchingGuard Width: 2.99in / 76mmGuard Length: 7.44in / 189mmGuard Thickness: 0.01in / 0.5mmTotal Weight: 1.30oz / 37gShown painted Black...VVV-C1281RRP £25.99 -
RC4WD Rancho RS9000 XL Shock Absorbers 80mm Z-D0077 TF2 G2 Suspension Shocks
RC4WD
MSRP: £47.49RRP £40.99Additional Information - RC4WD Rancho RS9000 XL Shock Absorbers 80mm This is the all new Licensed Scale Shock to hit the market. Licensed from Rancho. These new shocks feature a complete new design from the ground up and are built and ready to handle...Z-D0077MSRP: £47.49RRP £40.99 -
M3 M4 Long Straight Aluminum Rod Ends BLACK 10 Z-S1677 RC4WD Alt Z-S1375 End
RC4WD
MSRP: £40.99RRP £35.49Additional Information - M3/M4 Long Straight Aluminum Rod Ends (Black) (10)Perfect upgrade to replace your plastic rod ends. These aluminum rod ends are a great heavy duty upgrade replacement. Direct replacement to Z-S1375.Specifications: Manufactured...Z-S1677MSRP: £40.99RRP £35.49 -
CNC Aluminum Black M3 Bend Rod End 10 24mm RC4WD Z-S1452 G2 TF2 Crawler RC
RC4WD
MSRP: £27.49RRP £22.99Additional Information - Aluminum Black M3 Bend Rod End (10) Specifications:CNC Machined Rugged Aluminum ConstructionPre-Installed with a Stainless Steel Ball M3 ID Ball OpeningShaft Diameter: 0.22in / 5.6mmHead Diameter: 0.38in / 9.8mmBent Degree:...Z-S1452MSRP: £27.49RRP £22.99 -
Trailing Arm SMT10 Yeti Bomber Carbon Assault 10th Monster Truck Z-S2008 RC4WD
RC4WD
MSRP: £44.99Now: £38.99Was: £44.99Additional Information - Trailing Arm for SMT10, Yeti, Bomber, Carbon Assault 1/10th Monster TruckSpecifications:CNC MachinedBillet AluminumSilver Anodized Finish?�Length: 5.11in / 129.8mmTotal Weight: 2.79oz / 79.3gShown installed on RC4WD Carbon...Z-S2008MSRP: £44.99Now: £38.99Was: £44.99 -
RC4WD Rock Krawler Link Package AE Element RC Enduro Sendero RTR Truck Z-S1996
RC4WD
RRP £35.49RC4WD Rock Krawler Link Package for AE Element RC Enduro Sendero RTR TruckThe new Rock Krawler Link package is just what you need to top off your AE Element RC Enduro Sendero RTR Truck. The Rock Krawler links are CNC machined in billet aluminum...Z-S1996RRP £35.49 -
M3 Offset Long Aluminum Rod Ends BLACK 10 RC4WD Z-S1643 27.8mm Steering RC
RC4WD
RRP £34.99Additional Information - M3 Offset Long Aluminum Rod Ends (Black) (10)Perfect upgrade to replace your plastic rod ends. These aluminum rod ends are a great heavy duty upgrade replacement. Direct replacement to Z-S0400.Specifications:CNC MachinedBillet...Z-S1643RRP £34.99 -
FTX Outback Mini X/XP Optional Oil Filled Aluminum Shocks (4) FTX9447
FTX
RRP £37.99Additional Information - FTX OUTBACK MINI X/XP OPTIONAL OIL FILLED ALUMINUM SHOCKS (4FTX9447RRP £37.99 -
ProLine Power Stroke SCX10 Scaler SHOCKS 90 95mm Aly PRE BUILT 2 springs 6060-00
Pro-Line
MSRP: £44.99Now: £35.99Was: £44.99PRO-LINE PRO-LINE POWERSTROKE SCALER SHOCKS 90MM-95MM PAIRPro-Line Pro-Line Powerstroke Scaler Shocks 90mm-95mm Pair6060-00MSRP: £44.99Now: £35.99Was: £44.99Qty in Cart: 0Quantity:Price:MSRP: £44.99Now: £35.99Was: £44.99Subtotal: -
RC4WD Trail Finder 3 Front Shock Hoops Z-S2129 RC4WD aluminium mounts TF3
RC4WD
RRP £26.49Additional Information - RC4WD Trail Finder 3 Front Shock HoopsSpecifications:CNC MachinedBillet AluminumBlack Anodized FinishTotal Weight: 0.59oz / 17gShown installed on RC4WD Trail Finder 3 RTR Chassis for example (Not Included)What's Included:1x RC4WD...Z-S2129RRP £26.49 -
RC4WD Trail Finder 3 W56 2-Speed Transmission Shifting Assembly Z-S2126 RC4WD
RC4WD
MSRP: £39.49RRP £35.49Additional Information - RC4WD Trail Finder 3 W56 2-Speed Transmission Shifting Assembly Specifications:Stamped SteelStainless SteelBillet AluminumCNC MachinedTotal Weight: 1.04oz / 29.7gWhat's Included:1x RC4WD Trail Finder 3 W56 2-Speed Transmission...Z-S2126MSRP: £39.49RRP £35.49 -
RC4WD Trail Finder 3 Shifting and Servo Arm Assembly Z-S2112 RC4WD Complete TF3
RC4WD
MSRP: £45.99RRP £40.99Additional Information - RC4WD Trail Finder 3 Shifting and Servo Arm AssemblySpecifications:CNC MachinedBillet AluminumBlack Anodized FinishTotal Weight: 1.12oz / 32gShown installed on RC4WD Trail Finder 3 RTR Chassis for example (Not Included)What's...Z-S2112MSRP: £45.99RRP £40.99 -
Suspension Links for Cross Country Off-Road Chassis Z-S2048 RC4WD
RC4WD
MSRP: £26.49RRP £23.49Additional Information - Suspension Links for?�Cross Country Off-Road ChassisSpecifications:CNC MachinedBillet AluminumBlack Anodized FinishTotal Weight: 1.32oz / 37.6gShown installed on RC4WD Cross Country Off-Road RTR with Chubby Mini 3 TON Scale Jack...Z-S2048MSRP: £26.49RRP £23.49 -
Spring Damper Set for 1/24 Trail Finder 2 Z-S2046 RC4WD Shocks 5mm 23mm Length
RC4WD
RRP £22.49Additional Information - Spring Damper Set for 1/24 Trail Finder 2Specifications:ABS Plastic Injection MoldingHole to Hole (Compressed): 0.70in / 18mmHole to Hole (Uncompressed): 0.90in / 23mmOverall Length: 1.10in / 28mmTravel Length: 0.19in / 5.0mmEach...Z-S2046RRP £22.49 -
Super Soft Flex Leaf Springs for Gelande II (4) Z-S1897 RC4WD G2 101mm Spring
RC4WD
RRP £40.99Additional Information - Super Soft Flex Leaf Springs for Gelande II (4)Specifications:Super Durable Steel Leaf SpringsSoft Springs increases articulation over obstaclesScrew Hole OD: 0.12in / 3mmLength: 3.97in / 100.8mmWidth: 0.27in / 7.0mmTotal Weight:...Z-S1897RRP £40.99